Pipe Repair in Hodges, SC — Located Precisely, Fixed Permanently
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Hodges, SC use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
What Separates Precision Pipe Repair from Guesswork
The biggest cost variable in pipe repair isn't parts — it's how much structure gets opened to find and access the failure. Precise pre-repair location tools reduce that cost significantly.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
We use thermal imaging as a complement to acoustic detection — particularly useful for slab leaks and leaks inside insulated wall cavities where sound transmission is reduced.
🛠️
All Pipe Materials & Joining Methods
Our techs are proficient in copper sweating (soldering), press-fit connections (ProPress system), CPVC solvent welding, PEX crimp and expansion fitting installation, threaded galvanized repair, and ABS/PVC drain line work. We match the repair method and material to the existing pipe system rather than forcing incompatible transitions.
🔒
Pressure-Tested Before We Leave
Drain line repairs are water-tested by running fixtures through the repaired section and visually confirming no seepage at the repair joint and downstream.
Our Pipe Repair Services
What We Fix — Pipe by Pipe, Material by Material
Pipe failures have different causes depending on material type, age, water chemistry, and installation history. Here's how we address each category.
Copper
Copper Pipe Repair & Repipe
Copper failures most often involve pinhole corrosion in soft copper tubing from aggressive water chemistry, failed soldered joints, or fatigue cracks at fittings in high-vibration locations. We locate the failure precisely, cut out the failed section, and install either a sweated repair coupling or a press-fit connector — both rated to ASTM B88 standards for potable water service.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX — either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
PEX is also the material of choice for extending or reconfiguring supply runs during remodel work. Its flexibility reduces fitting count and eliminates the need for torch work inside walls.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
We also inspect upstream of the burst for additional sections that froze but haven't yet failed — because a partially-thawed line sometimes shows multiple failure points only after pressure is restored.
Slab Leaks
Under-Slab Pipe Leak Repair
Slab leak rerouting is often more cost-effective than direct access, particularly for longer runs or under tiled floors. We present the options honestly with pricing so you can choose based on your priorities.
Full Repipe
Whole-House Repipe Service
A full repipe in Hodges typically completes in 2–3 days for a standard single-family home. You're without water for a portion of each day; we plan the schedule to minimize disruption to occupied rooms.
Here's how a Masters Plumbing Service pipe repair call plays out in Hodges, SC.
1
Call & Describe — We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see — water stain on a ceiling, drop in water pressure, wet flooring — helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
This detection step routinely saves homeowners $500–$2,000 in unnecessary drywall removal compared to opening walls speculatively.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test — Then You're Done
Repair executes immediately on approval. After the repair, we repressurize and hold a pressure test to confirm the failure is fully resolved — not partially. The access opening is left clean for your drywall patch or left ready for your contractor.
Customer Reviews
Real Pipe Repair Reviews from Hodges, SC Homeowners
★★★★★
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling — no torch in my wall — pressure tested, and patched the drywall themselves. Two hours total.
— N. Bergman, Hodges
★★★★★
Had an under-slab leak diagnosed by Masters Plumbing Service with acoustic equipment. They found the leak at 6 feet from the wall — a single copper elbow that had developed a pinhole. Presented three options: direct slab access, reroute through the wall framing above, or copper lining. I chose the reroute — they ran a new PEX line through the crawl space and connected at both ends without touching the slab. Pressure tested, verified no remaining drop. No jackhammering at all.
— O. & R. Adeyemi, Hodges, SC
★★★★★
I noticed my water meter spinning with all fixtures off — confirmed a leak in the supply system. Masters Plumbing Service ran a pressure test and acoustic scan, found a pinhole in a copper section under the slab in the utility room. They rerouted the line through the wall above slab, tested, and closed out the permit. The reroute was exactly the same cost as direct slab access would have been, but no damaged floor tile.
— F. Okoro, Hodges, SC
Common Questions
What to Know Before Calling for Pipe Repair in Hodges, SC
A slow pinhole leak inside a wall can run for months before surface damage appears. By the time you see a stain, the moisture intrusion is typically already significant. If your meter shows movement with everything off, call us — we can pressure-test and locate it before it becomes a major remediation project.
In some cases — particularly for older copper systems with multiple pinhole failures along a supply run — rerouting the line through accessible framing rather than repairing it in place is more practical and more permanent. We present both options when they're both viable.
Repair options include direct slab access (jackhammer to the pipe, repair, patch), rerouting the supply line above slab through framing, and for copper systems with multiple pinhole failures, epoxy pipe lining from inside the pipe without excavation. We use acoustic and thermal detection to locate the leak before recommending a repair approach.
We assess galvanized condition when we're on-site — visible exterior corrosion, interior scale visible at the cut failure point, and water pressure readings all tell us how advanced the system deterioration is. We give you the repair-vs-repipe math honestly so you can make the decision that fits your timeline and budget.
A single localized pipe repair — finding and fixing one failure point — typically takes 1.5–3 hours including detection, access, repair, and pressure testing. Slab leak reroutes run 3–5 hours depending on the routing path and pipe length. A full-house repipe is a multi-day project — typically 2–4 days for a standard single-family home depending on size and pipe count.
Our pipe repair quote includes clean access cuts and leaving the opening ready for patching — with a clean, straight cut that accepts a standard drywall patch. We can typically patch the access opening as part of the job on request, though finish painting and texture matching are typically handled by the homeowner or a drywall contractor for best cosmetic results.
Service Area
Pipe Repair Covering Hodges and All of Hodges, SC
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Hodges homes and businesses.
